Biplane Build Notes Worksheet
Wood Tech 1 • Project Guide
Biplane Build Notes
Name:
Date:
Shop Word Bank
• bandsaw • clamps • compass • dowel • drill press • gaps • grain • miter saw • pressure • relief cuts • scrap wood • scroll saw • square • vise • X
Part 1: Making the Main Body
Slides 2–15
1. Cut a 2½" board into sections, each inches long, using the small .
2. Spread glue on pieces, stack all three together, and hold them tight with two . Make sure the wood is even and there are no .
3. Square the ends and trim both ends on the yellow DeWalt saw so the body is inches long.
4. Use a ruler to draw an from corner to corner on one end to find the center, then trace the body template.
5. Draw for the cockpit and cut them first on the to relieve from the blade when making curved cuts.
Part 2: Landing Gear & Rear Tail Wings
Slides 16–17, 35
6. For the landing gear, choose a ¾" thick piece of and make sure the wood runs left to right.
7. Cut out the landing gear shape using the .
8. To assemble the landing gear, draw an X to find the center, drill with the bit labeled , and glue in the axles and wheels.
9. Get ⅜" thick boards from the black milk crate for the rear tail wings. Trace the wide tail piece with the grain going , and the tall fin with the grain going .
Part 3: Creating the Engine Block
Slides 18–29
10. Safely cut blocks (3¼" × 3¼", ⅝" thick) on the miter saw. Turn one block 180° so the opposes the other block before gluing and clamping.
11. Draw an X from corner to corner, then use a to draw lines through the center.
12. Use a to draw two circles: the first with a radius of " and the second with a radius of ".
13. Connect the V-cuts and drill the cylinder holes on the . Safety rule: Always hold the while drilling!
14. Sand off saw and pencil marks, then glue pieces of ⅜" into the holes. Let dry for 10 minutes and trim.
Part 4: Plane Wings
Slides 30–34
15. Cut one short wing ( ") and one long wing ( "). Mark the center of both using an X and a square.
16. On the short wing, draw a vertical line " from each side. Line up the center marks and transfer those lines to the long wing, then mark the drill spots.
17. Cut out the rounded wing ends on the , drill the holes with the preset drill press, and sand away all saw and pencil marks.
18. Cut pieces of ⅜" dowel to " long, then glue and carefully clamp the wings together.
End-of-Presentation Review Questions
1. Why is it important to cut relief cuts in the cockpit area before making the curved bandsaw cut?
2. Explain why wood grain direction matters when laying out the landing gear, tail wings, and engine block.
3. List two important safety habits shown in the presentation when using the miter saw or drill press.
4. Why do we sand away all saw marks and pencil marks before gluing parts like the wings or engine block?
Quick Check: Circle True or False
1. When gluing the 3 main body pieces, small gaps between boards are fine. True / False
2. Drawing an X from corner to corner helps you find the exact center of a piece. True / False
3. You should hold the vise while drilling cylinder holes on the drill press. True / False
4. Both the wide tail wing and the tall tail fin should have their grain running the same way. True / False
Biplane Parts & Process Activity
Wood Tech 1 • Follow-Along Activity
Biplane Parts & Process
Name:
Date:
Activity 1: Part Identification & Spec Sheet
Use Slides 1–35
Follow along with the presentation to identify each biplane part from the Part Bank, then record its key dimensions and the main tool used to cut or drill it.
Part Bank: Main Body • Landing Gear • Rear Tail Wings • Engine Block • Plane Wings • Wing Struts & Cylinders
| Part Name |
Role in the Biplane |
Dimensions / Material |
Main Tool Used |
|
3 stacked sections glued together with cockpit cutouts |
|
|
|
Scrap wood base that holds the axles and wheels |
|
|
|
Wide horizontal piece & tall fin from the milk crate |
|
|
|
2 opposing-grain squares with V-cuts & 8 holes |
|
|
|
One short & one long rounded board stacked together |
|
|
|
Round wooden rods connecting wings & engine |
|
|
Activity 2: Grain Direction Spot-Check
Slides 16, 17, 20
In woodworking, grain direction affects strength. Follow the slides to record the correct grain rule for each part below.
1. Landing Gear (Slide 16)
Which way must the grain run?
2. Rear Tail Wings (Slide 17)
Wide wing vs. tall fin grain:
3. Engine Block (Slide 20)
How are the 2 blocks oriented?
Activity 3: Build Process Sequencing
Number steps 1–5
Use the PDF slides to put each build process in the correct order from 1 (first) to 5 (last).
A. Main Body Process (Slides 2–13)
Draw relief cuts for the cockpit and cut them first on the bandsaw.
Cut a 2½" board into three 12" sections on the small miter saw.
Trace the top/bottom view and cut the side profile on the bandsaw.
Spread glue on two pieces, stack all three, and clamp tightly with no gaps.
Square the ends, trim to 11" long, and draw an X + body template.
B. Engine Block Process (Slides 18–29)
Drill cylinder holes on the drill press while holding the vise.
Turn one block 180° so the grain opposes, then glue and clamp together.
Sand off saw and pencil marks, then glue 8 pieces of ⅜" dowel into the holes.
Safely cut two 3¼" × 3¼" blocks on the miter saw.
Draw an X, square center lines, two compass circles (1⅛" & 1⅜"), and V-cuts.
Activity 4: Plan & Process Check
1. On Slide 31, why do we line up the center marks of the 11½" short wing and transfer the 2" lines to the 13½" long wing?
2. Looking at Slide 28 (Engine Block) and Slide 35 (Landing Gear), how is the drill press used safely and accurately?
3. Which part of the biplane build do you think will require the most careful measuring, and why?