Speed Demons Slides Propeller Car Grand Prix • Days 1–2
Speed Demons
Your mission: Design, solder, and race the fastest propeller-powered car over a set distance—and prove the physics behind its speed!
10-Day Build
40 min per day
Real Soldering
Motor + Switch Circuit
Race Day Goal
Max Speed & Energy Proof
Day 1 • Motion & Speed
How Do We Measure Speed?
The Speed Formula
\[ s = \frac{d}{t} \]
\(s\) = Speed (m/s) • \(d\) = Distance (m) • \(t\) = Time (s)
Example Pit Stop
A car travels 6 meters in 3 seconds .
\(s = \frac{6\text{ m}}{3\text{ s}} = 2\text{ m/s}\)
Average Speed
Total distance divided by total time—even if the car speeds up or slows down!
Day 1 Mini-Lab • 15 Minutes
Hallway Speed Trials
1. Measure
Mark a 4-meter track on the floor with masking tape.
2. Time
Time a partner doing a slow walk , fast walk , and crab walk .
3. Calculate
Use \(s = \frac{d}{t}\) to find each speed in m/s on your lab sheet.
Safety Check: Keep backpacks clear of the track and walk—no running indoors!
Day 2 • Graphing Motion
Reading a Distance-Time Graph
X-Axis
Time (seconds) goes along the bottom.
Y-Axis
Distance (meters) goes up the side.
Slope
Steeper line = Faster speed!
3 Line Clues
Straight Diagonal: Constant speed
Flat Horizontal: Stopped (0 m/s)
Curving Upward: Speeding up (accelerating!)
Day 2 • Race Day Preview
How We Will Graph Our Cars
On Race Day, timers will stand at 1 m , 2 m , 3 m , and 4 m along the track.
0 m
0.0 s
1 m
Split 1
2 m
Split 2
4 m
Finish!
Plot (Time, Distance) pairs and connect the dots to see where your car accelerated!
Pit Crew Check-Out
Before You Leave Today...
1. If Car A travels 4 m in 2 s and Car B travels 4 m in 4 s, which car has a steeper line on a distance-time graph?
2. What is one design idea you already have to make your propeller car fast?
Speed Demons Lab Sheet Propeller Car Grand Prix • Days 1–2
Speed Demons Lab Sheet
Name: __________________________
Date: ____________ Period: ______
SPEED FORMULA
Speed equals distance divided by time. Standard unit: meters per second (m/s).
\( s = \frac{d}{t} \)
Part 1: Hallway Speed Trials (4-Meter Track)
Measure a 4-meter track. Time each motion twice, find the average time, then calculate speed.
Motion Type
Distance (m)
Trial 1 (s)
Trial 2 (s)
Avg Time (s)
Speed (m/s)
Slow Walk
4.0 m
Fast Walk
4.0 m
Crab Walk
4.0 m
Part 2: Pit Crew Speed Calculations (Show Your Work!)
1. A propeller car travels 6 meters in 2.5 seconds. What is its average speed?
2. Car A goes 5 meters in 2 seconds. Car B goes 8 meters in 4 seconds. Which car is faster? Prove it with math.
3. If a propeller car moves at 2.0 m/s for 3 seconds, how far does it travel?
Continue to Page 2 for Distance-Time Graphing Practice.
Part 3: Distance-Time Graph Practice
Name: ________________________
Below is split-time data for a test propeller car on a 4-meter track. Plot the points on the grid, label both axes, and connect the points with a line.
Time (s)
0 s
1 s
2 s
3 s
4 s
5 s
Distance (m)
0 m
0.5 m
1.5 m
3.0 m
3.0 m
4.0 m
Distance (m)
Time (s)
1. Between which two seconds was the car moving the FASTEST? How can you tell from the graph?
2. What happened between 3 s and 4 s? What does the flat line mean?
3. Calculate the car's overall average speed for the entire 5-second run (4 m total):
Speed Demons Teacher Guide Teacher Pacing & Answer Key • Days 1–2
Speed Demons Teacher Guide
2 Days × 40 Min
Day 1 Pacing (40 min)
0–8 min: Launch Propeller Car Grand Prix (Slides 1–2). Introduce \(s = d/t\).
8–25 min: Hallway Speed Trials Mini-Lab (Slide 3). Students time 3 motions over 4 m.
25–36 min: Complete Part 1 averages & Part 2 practice problems.
36–40 min: Quick debrief on units (m/s) & average speed.
Day 2 Pacing (40 min)
0–10 min: Distance-Time Graph direct instruction (Slides 4–5).
10–25 min: Students plot test car data & answer Part 3 questions.
25–35 min: Review graph shapes (steep = fast, flat = stopped).
35–40 min: Pit Crew Check-Out (Slide 6).
Materials & Differentiation
Prep: Masking tape for 4-meter tracks (1 per 4–5 students), stopwatches/timers, calculators.
Support / Extension: Pre-label graph axes (0–5 s on X, 0–4 m by 0.5 m on Y) for students needing scaffolding. Challenge early finishers to calculate the speed for each 1-second interval on the graph.
Lab Sheet Answer Key
Part 1 (Mini-Lab): Answers vary. Check that students averaged Trial 1 and Trial 2, then divided 4.0 m by Average Time.
Part 2, Q1: \(s = 6\text{ m} \div 2.5\text{ s} = \mathbf{2.4\text{ m/s}}\)
Part 2, Q2: Car A: \(5 \div 2 = \mathbf{2.5\text{ m/s}}\). Car B: \(8 \div 4 = \mathbf{2.0\text{ m/s}}\). Car A is faster.
Part 2, Q3: \(d = s \times t = 2.0\text{ m/s} \times 3\text{ s} = \mathbf{6.0\text{ m}}\)
Part 3, Q1: Fastest between 2 s and 3 s (traveled 1.5 m in 1 s). The line is steepest in this section.
Part 3, Q2: The car stopped (0 m/s) between 3 s and 4 s; distance stayed at 3.0 m, shown by a flat horizontal line.
Part 3, Q3: Overall average speed = \(4.0\text{ m} \div 5.0\text{ s} = \mathbf{0.8\text{ m/s}}\)
Slide 6 Exit Check: Car A (4 m / 2 s = 2 m/s) has the steeper line because it is faster than Car B (1 m/s).
Energy Detectives Slides Propeller Car Grand Prix • Days 3–4
Energy Detectives
Where does your car's speed come from? Today we trace every form of energy—from stored battery power to spinning propellers!
Potential & Kinetic
Stored vs. Motion
Gravitational PE
Ramp Mini-Lab
Transformations
Battery to Speed
Day 3 • Stored vs. Moving Energy
Potential, Kinetic & Gravitational Energy
Potential Energy
Stored energy waiting to be released—like a battery or a stretched rubber band.
Kinetic Energy
Energy of motion! Faster speed or heavier mass means more kinetic energy.
Gravitational PE
Stored energy from height. Higher ramp = more GPE = faster roll at the bottom!
Day 3 Mini-Lab • 15 Minutes
Ramp Drop: Height vs. Speed
1. Build: Stack 1 textbook under a ruler/cardboard ramp.
2. Release: Let a marble or toy car roll (do not push!) and measure how far it rolls.
3. Raise: Repeat with 2 books and 3 books .
What Are You Observing?
At the top, the marble has Gravitational Potential Energy . Rolling down transforms it into Kinetic Energy !
Day 4 • Four Key Energy Forms
Energies Inside a Propeller Car
Electrical Energy
Moving electrons flowing from the battery through your soldered wires.
Electromagnetic Energy
Inside the motor, electric current creates magnetic fields that spin the shaft!
Mechanical / Kinetic
The spinning propeller pushes air backward, launching the car forward.
Thermal Energy
Heat from friction in the wheels/axles and warm wires—energy lost from speed!
Day 4 • Conservation of Energy
The Propeller Car Energy Chain
Chemical PE
Battery
Electrical
Wires & Switch
Electromagnetic
DC Motor
Kinetic + Thermal
Motion & Heat
Energy is never created or destroyed—it only transforms from one form to another!
Engineering Connection
Think Like a Race Engineer
Why do rubbing wheels and crooked axles slow down a propeller car?
They waste useful kinetic energy by turning it into unwanted thermal (heat) energy!
Energy Detectives Worksheet Propeller Car Grand Prix • Days 3–4
Energy Detectives Worksheet
Name: __________________________
Date: ____________ Period: ______
Part 1: Gravitational Potential Energy (GPE) Ramp Mini-Lab
Release a marble or toy car from the top of the ramp (do not push). Measure how far it rolls from the bottom of the ramp.
Ramp Height
Trial 1 (cm)
Trial 2 (cm)
Average (cm)
Relative Speed (Slow/Med/Fast)
1 Book High
2 Books High
3 Books High
Mini-Lab Conclusion: How did increasing the ramp height change the Gravitational Potential Energy and Kinetic Energy?
Part 2: Identify the Energy Form
Write the best energy form for each clue: Potential, Kinetic, Gravitational PE, Electrical, Electromagnetic, or Thermal .
1. Energy stored inside an unused AA battery:
2. Energy of moving electrons flowing through copper wire:
3. Magnetic field inside the DC motor that spins the shaft:
4. Energy of the propeller car zooming down the track:
5. Heat created when axles rub against the cardboard body:
6. Energy stored when a car is lifted to the top of a hill:
Continue to Page 2 for Energy Transformation Mapping.
Part 3: Propeller Car Energy Transformations
Name: ________________________
Fill in the 4 boxes below to show how energy transforms from the battery to your moving propeller car. Name the car part and the energy form at each step.
Step 1: Power Source
Step 2: Wires & On/Off Switch
Step 3: Inside the DC Motor
Step 4: Propeller & Wheels Moving
Part 4: Energy Efficiency & Design Thinking
1. Why does your motor feel slightly warm after running for 30 seconds? Which energy transformation is happening?
2. If you want your car to be the FASTEST on Race Day, how can you reduce wasted thermal energy (friction) in your design?
3. Multiple Choice: When you flip the switch ON, what is the correct order of energy transformations?
A. Kinetic → Electrical → Thermal → Potential
B. Chemical Potential → Electrical → Electromagnetic → Kinetic
C. Gravitational Potential → Electromagnetic → Electrical → Kinetic
D. Thermal → Chemical Potential → Kinetic → Electrical
Energy Detectives Teacher Guide Teacher Pacing & Answer Key • Days 3–4
Energy Detectives Teacher Guide
2 Days × 40 Min
Day 3 Pacing (40 min)
0–10 min: Potential, Kinetic, and Gravitational PE (Slides 1–2).
10–28 min: Ramp Drop Mini-Lab (Slide 3, Worksheet Part 1).
28–40 min: Complete Mini-Lab conclusion & Part 2 energy matching.
Day 4 Pacing (40 min)
0–12 min: Electrical, Electromagnetic & Thermal energy in motors (Slides 4–5).
12–32 min: Complete Worksheet Parts 3–4 (Energy Transformation Chain).
32–40 min: Class share-out on reducing friction (Slide 6).
Mini-Lab Prep & Demo Tip
Materials: Grooved rulers or cardboard ramps, 3 textbooks per group, marbles or small toy cars, meter sticks. Demo Idea: Hold up a bare DC motor and battery so students can feel the slight warmth (thermal energy) and hear/see the spinning shaft (electromagnetic → kinetic).
Worksheet Answer Key
Part 1 Conclusion: Raising the ramp height increased the marble's Gravitational Potential Energy, which transformed into more Kinetic Energy, making it roll faster and farther.
Part 2: 1. Potential (Chemical PE) • 2. Electrical • 3. Electromagnetic • 4. Kinetic • 5. Thermal • 6. Gravitational PE.
Part 3 Energy Chain: Step 1: Battery (Chemical Potential Energy) → Step 2: Wires/Switch (Electrical Energy) → Step 3: DC Motor (Electromagnetic Energy) → Step 4: Propeller/Car (Kinetic Energy + Thermal Energy).
Part 4, Q1: Some electrical/electromagnetic energy transforms into thermal energy (heat) due to electrical resistance and friction inside the motor.
Part 4, Q2: Use straight axles, smooth straws as axle bearings, light materials, and make sure wheels don't rub against the body.
Part 4, Q3: B (Chemical Potential → Electrical → Electromagnetic → Kinetic).
Circuit Sparks Slides Propeller Car Grand Prix • Days 5–6
Circuit Sparks
Time to wire up your power! Learn how simple on/off circuits work and solder your own motor-switch-battery harness safely.
Closed Loop
On/Off Switch Control
Safety First
Goggles & Iron Stands
Clean Joints
Strong & Shiny Solder
Day 5 • How Your Switch Works
Simple On/Off Circuit
OFF = Open Circuit
There is a gap inside the switch. Electrons cannot complete the loop, so the motor stays OFF .
ON = Closed Circuit
The switch bridges the gap! Electrical energy flows from battery → switch → motor → battery.
Tip: Flipping the two wires on the motor reverses which way the propeller spins!
Day 5 • Mandatory Safety
5 Golden Soldering Rules
1. Safety Goggles ON at all times—no exceptions.
2. Hold ONLY the handle. The metal tip is over 350°C (660°F)!
3. Always return the iron to its metal stand —never lay it on the table.
4. Tie back hair & sleeves and keep fingers away from the hot tip.
5. Wash hands with soap and water when finished soldering.
Day 6 • Soldering Technique
How to Make a Clean Solder Joint
1. Twist
Hook and twist bare wire tightly onto the metal tab.
2. Heat
Touch the iron tip to BOTH the wire and tab for 2 seconds.
3. Feed
Touch solder wire to the hot joint until it flows smoothly.
4. Cool
Lift solder, then iron. Hold still 3 seconds until shiny!
Day 6 • Build Your Harness
3 Connections to Solder
1
Red Battery Wire (+) → Solder to Switch Pin 1 .
2
Switch Pin 2 → Solder a jumper wire to Motor Tab A .
3
Black Battery Wire (−) → Solder to Motor Tab B .
Circuit Check-Out
Motor Won't Spin? Check These 3 Things
1. Tug Test: Gently tug each solder joint—does any wire slip loose?
2. Short Circuit: Are bare red and black wires touching anywhere?
3. Battery & Switch: Is the battery fresh and the switch flipped ON?
Circuit Sparks Build Guide Propeller Car Grand Prix • Days 5–6
Circuit Sparks Build Guide
Name: __________________________
Date: ____________ Period: ______
Part 1: Blueprint Your Simple On/Off Circuit
Draw and label a closed-loop circuit connecting a Battery Pack , an On/Off Switch , and a DC Motor . Use arrows to show the path of electrical energy.
1. Explain the difference between an OPEN circuit and a CLOSED circuit when you flip your switch:
2. Why is it important to keep bare red (+) and black (−) wires from touching each other?
Part 2: Soldering Safety Certification
☐ I will wear safety goggles at all times at the soldering station.
☐ I will only hold the insulated handle and never touch the hot metal tip.
☐ I will always place the soldering iron back into its metal stand when not in use.
☐ I will tie back loose hair/sleeves and wash my hands after soldering.
Student Signature: _________________________ Teacher Initials: ________
Complete Part 2 and get Teacher Initials before using a soldering iron.
Part 3: Solder & Test Your Motor Harness
Name: ________________________
Wiring & Soldering Checklist (Check off each step)
☐ Step 1: Strip 1 cm of plastic insulation off the ends of your wires.
☐ Step 2: Twist the Red (+) Battery Wire onto Switch Pin 1 and solder cleanly.
☐ Step 3: Twist a jumper wire onto Switch Pin 2 and solder cleanly.
☐ Step 4: Solder the other end of the jumper wire to Motor Tab A .
☐ Step 5: Twist the Black (−) Battery Wire onto Motor Tab B and solder cleanly.
☐ Step 6: Wrap exposed metal joints with electrical tape so they cannot touch.
Part 4: Harness Quality & Spin Test
Inspection Check
Pass / Fix
Notes
Tug Test (All 4 joints hold tight)
Switch OFF (Motor stays stopped)
Switch ON (Motor spins smoothly)
Propeller Thrust Check: Put the propeller on the shaft and turn the switch ON. Which way does the air blow? (If it blows forward instead of backward, how will you fix it?)
Energy Check: Which two energy forms are happening inside your spinning motor right now?
Circuit Sparks Teacher Guide Teacher Pacing & Safety Guide • Days 5–6
Circuit Sparks Teacher Guide
2 Days × 40 Min
Day 5 Pacing (40 min)
0–12 min: Open vs. Closed circuits & Soldering Safety (Slides 1–3).
12–25 min: Students complete Build Guide Page 1 & sign Safety Pledge.
25–40 min: Teacher demo of 4-step soldering; students strip & pre-twist wires at desks.
Day 6 Pacing (40 min)
0–5 min: Review 3 solder connections (Slides 4–5).
5–32 min: Station Rotation: Pairs/groups solder at supervised stations while others prep chassis sketches.
32–40 min: Tug test, spin test, and troubleshooting (Slide 6).
Classroom Soldering Management (6th Grade)
Setup: Set up 3–4 soldering stations with lead-free solder, damp sponges, helping-hands clips, and safety goggles. Keep batteries OUT of battery holders while soldering to prevent accidental shorts.
Efficiency Tip: Have students pre-twist all wire-to-pin connections at their desks before stepping up to a soldering station—this cuts station time to 2–3 minutes per student!
Build Guide Answer Key
Part 1 Diagram: Must show a single closed loop: Battery (+) → Switch → Motor → Battery (−).
Part 1, Q1: An open circuit has a break/gap (switch OFF), so electricity cannot flow. A closed circuit has a complete loop (switch ON), so electricity flows to the motor.
Part 1, Q2: If bare red and black wires touch, it creates a short circuit —electricity skips the motor, drains the battery, and makes the wires dangerously hot (thermal energy).
Part 4 Thrust Check: Air should blow backward to push the car forward. If it blows forward, swap the wires on the motor tabs (or flip the propeller).
Part 4 Energy Check: Electrical energy transforms into electromagnetic energy (and kinetic + thermal energy).
Prop Car Builders Slides Propeller Car Grand Prix • Days 7–8
Prop Car Builders
Build your chassis, mount your soldered motor circuit, and engineer the fastest car on the track!
Chassis Choice
Cardboard, Wood, 3D Print
Speed Physics
Low Mass & Low Friction
Test & Tune
Iterate Before Race Day
Day 7 • Materials & Design
Pick Your Chassis Strategy
Cardboard
Super lightweight and easy to cut—just reinforce axles so it stays stiff!
Wood
Strong and rigid for straight axles—keep it narrow to avoid extra weight.
3D Printed
Aerodynamic and precise—check wheel clearance before gluing parts.
Day 7 • Engineering for Speed
3 Secrets to a Faster Car
1. Cut Unnecessary Mass
Less mass means your propeller accelerates the car faster from the starting line.
2. Eliminate Axle Friction
Slide axles through smooth plastic straws—less thermal energy wasted!
3. Aim Straight & Clear the Prop
Parallel axles keep the car straight; raise the motor so the propeller never hits the floor.
Day 7 • Assembly Checklist
Mounting the Motor, Battery & Switch
Propeller Clearance: Mount the motor high enough on a block or rear tower so blades spin freely.
Balance Weight: Place the battery pack low and centered so the car doesn't tip.
Easy Switch Access: Tape or glue the switch on top so you can flip it ON cleanly at the start line.
Secure Wires: Tape loose wires flat so they never tangle in the spinning propeller!
Day 8 • Test & Iterate
Test Track Pit-Stop Loop
1. Test Run
Time your car on the practice track and watch how it steers.
2. Diagnose
Veering left? Wheels wobbling? Battery sliding?
3. Upgrade
Make ONE change at a time and re-test to see if speed improves!
Impound Check
Ready for Race Day?
✓ Wheels spin freely with zero rubbing.
✓ Propeller blows air backward to push the car forward.
✓ Switch turns the motor ON and OFF reliably.
✓ Team name is labeled clearly on the chassis!
Prop Car Builders Blueprint Propeller Car Grand Prix • Days 7–8
Prop Car Builders Blueprint
Name: __________________________
Date: ____________ Period: ______
Part 1: Car Chassis Blueprint (Top & Side View)
Sketch your car design below. Label: chassis material, wheels, axles, motor mount, propeller, battery pack, and on/off switch .
Part 2: Speed Engineering Plan
1. Which chassis material are you using (cardboard, wood, or 3D-printed body) and why?
2. How will you reduce friction (wasted thermal energy) on your wheels and axles?
3. How will you keep the propeller blades from hitting the ground or wires?
Continue to Page 2 for your Day 8 Test-Track Tuning Log.
Part 3: Day 8 Test-Track Tuning Log
Name: ________________________
Test your car on the practice track. Record the time, calculate speed, write down what happened, and describe ONE change you made before the next test!
Test Run
Distance (m)
Time (s)
Speed (m/s)
Observation & Upgrade Made
Run 1
Run 2
Run 3
Part 4: Final Pre-Race Inspection
☐ All 4 wheels spin smoothly without rubbing the chassis.
☐ Propeller clears the floor and wires by at least 1 cm.
☐ Switch turns the car ON/OFF cleanly and air blows backward.
☐ Battery pack is securely attached and balanced.
Which single upgrade improved your car's speed the most during testing?
Prop Car Builders Teacher Guide Teacher Pacing & Workshop Guide • Days 7–8
Prop Car Builders Teacher Guide
2 Days × 40 Min
Day 7 Pacing (40 min)
0–8 min: Chassis options & 3 Speed Secrets (Slides 1–4).
8–18 min: Students complete Blueprint Page 1 (sketch + plan).
18–36 min: Build chassis, attach straws/axles/wheels, mount motor harness.
36–40 min: Clean-up & label cars with team names.
Day 8 Pacing (40 min)
0–5 min: Review Test-Track Pit-Stop Loop (Slide 5).
5–33 min: Finish assembly & run 3 timed practice runs (Blueprint Page 2).
33–40 min: Final Pre-Race Inspection (Slide 6) & store cars safely.
Materials & Glue Station Tips
Supplied Kits: Motors, wires, batteries, propellers, wheels, axles, on/off switches. Body Materials: Cardboard, craft/balsa wood, 3D-printed bodies, plastic straws (for axle bearings), hot glue/white glue, masking tape. Tip: Remind students never to glue axles directly to the chassis—always thread axles through a straw glued to the chassis!
Common Build Issues & Quick Fixes
Problem on Test Track
Likely Cause & Coaching Fix
Car goes backward
Propeller is pushing air forward. Flip the propeller or swap the motor wires.
Motor spins, car doesn't move
Wheels are rubbing the body (too much friction), or car is too heavy. Trim rubbing edges or lighten chassis.
Car curves sharply into wall
Axles are not parallel. Re-align axle straws perpendicular to the centerline.
Propeller hits the floor
Motor is mounted too low. Add a small cardboard or wood riser block under the motor.
Race Day Showdown Slides Propeller Car Grand Prix • Days 9–10
Race Day Showdown
It's time to race! Clock your official speed over the 4-meter track, graph your car's motion, and prove the energy behind your build.
Day 9: Time Trials
3 Official Runs + Splits
Day 10: Data Lab
Speed Math & Graphing
Energy Defense
Explain Every Transform
Day 9 • Official Track Rules
4-Meter Grand Prix Track
1. Zero Push Rule: Flip your switch ON at the 0 m line and let go—no pushing!
2. 4 Timers: Student timers stand at 1 m, 2 m, 3 m, and 4 m to capture split times.
3. Best of 3: Every team gets 3 official runs. Your fastest run counts for the leaderboard!
4. Pit Crew Respect: Cheer for every team and keep the track lane clear.
Day 10 • Motion Analysis
Graphing Your Car's Fastest Run
1. Calculate
Find your average speed: \(s = \frac{4.0\text{ m}}{\text{Finish Time}}\).
2. Plot Splits
Plot (0 s, 0 m) plus your 1 m, 2 m, 3 m, and 4 m split times.
3. Interpret
Where is your line steepest? That's where your car hit top speed!
Day 10 • Final Science Check
Prove Your Physics!
On your Race Report, be ready to explain:
• How Chemical Potential Energy became Electrical → Electromagnetic → Kinetic Energy .
• Where Thermal Energy (friction/heat) slowed your car down.
• How your car would gain Gravitational Potential Energy if it raced up a ramp!
Grand Prix Awards
Congratulations, Engineers!
Speed Champion
Fastest average speed over 4 meters
Cleanest Circuit
Best soldering & reliable switch
Friction Fighter
Straightest, smoothest chassis build
Race Day Showdown Report Propeller Car Grand Prix • Days 9–10
Race Day Showdown Report
Name: __________________________
Date: ____________ Period: ______
Part 1: Official 4-Meter Time Trials (Split Times)
Record the time (in seconds) when your car passes each meter mark. Calculate the overall average speed for each trial.
Trial
0 m (s)
1 m Split (s)
2 m Split (s)
3 m Split (s)
4 m Finish (s)
Avg Speed (m/s)
Trial 1
0.0 s
Trial 2
0.0 s
Trial 3
0.0 s
Part 2: Show Your Fastest Trial Speed Math
1. Calculate your car's average speed on its FASTEST trial using \( s = \frac{d}{t} \):
2. Calculate your car's speed during the FIRST meter (0 m to 1 m) vs. the LAST meter (3 m to 4 m). Did your car speed up or slow down?
3. If your car kept its fastest average speed for 10 seconds, how far would it travel?
Continue to Page 2 to graph your car's run and explain its energy transformations.
Part 3: Your Car's Distance-Time Graph
Name: ________________________
Plot your FASTEST trial's split times (0 m, 1 m, 2 m, 3 m, 4 m). Label the time scale on the X-axis and distance (0–4 m) on the Y-axis.
Distance (m)
Time (s)
Part 4: Energy Transformation Defense & Reflection
1. Trace the complete energy transformation in your car from battery to finish line (include potential, electrical, electromagnetic, kinetic, and thermal energy):
2. If you raced your car UP a ramp instead of a flat floor, what would happen to its speed and Gravitational Potential Energy?
3. What is one change you would make to build an even faster car next time?
Race Day Showdown Teacher Guide Teacher Pacing & Assessment Rubric • Days 9–10
Race Day Showdown Teacher Guide
2 Days × 40 Min
Day 9 Pacing (40 min)
0–5 min: Review Track Rules & assign 4 split-time timers (Slides 1–2).
5–35 min: Official 4-Meter Time Trials (3 runs per car; record splits in Part 1).
35–40 min: Announce Day 9 leaderboard & store cars.
Day 10 Pacing (40 min)
0–6 min: Review speed calculations & graphing (Slides 3–4).
6–32 min: Students complete Race Report Parts 2–4 (graph + energy defense).
32–40 min: Grand Prix Awards & unit wrap-up (Slide 5).
4-Meter Track & Timer Tip
Tape a 4-meter lane in the hallway or classroom with clear marks at 0 m, 1 m, 2 m, 3 m, and 4 m . Assign 4 students with stopwatches (one at each meter mark); all 4 start on "GO!" and stop as the car's nose crosses their line.
Propeller Car Grand Prix Rubric (100 pts)
Category
Mastery (Full Points)
Points
Soldered Circuit
Followed all safety rules; clean solder joints; on/off switch reliably powers motor.
25 pts
Car Engineering
Completed blueprint; car rolls smoothly over 4 m with low friction and clear propeller.
25 pts
Speed & Graphing
Accurate \(s = d/t\) calculations with units (m/s); properly labeled & plotted distance-time graph.
25 pts
Energy Explanation
Accurately traces chemical PE → electrical → electromagnetic → kinetic + thermal energy, plus GPE ramp reasoning.
25 pts